So far, though, the rings have not moved during the firing of some 120 rounds of. I was a bit skeptical the rings would hold tightly enough to prevent creeping forward under recoil. There is no notch or slot to prevent ring movement. These rings clamp to the integral rails in the receiver. I used the supplied rings to fit a Weaver Grand Slam 3-10x40mm scope.
The downside of the single-stack magazine is it takes up more space vertically than a double-stack magazine, projecting from the bottom of the rifle. The T3’s single stack magazine feeds short magnum cartridges straight into the chamber, smoothly and with complete reliability. I’ve seen examples in which cartridges would sometimes bind when making the “turn” from beneath the left or right feed rail. The newer short magnum cartridges don’t always feed well from Mauser-type, double-stack magazines. I don’t know of a rifle currently being made which has a slicker, smoother working action than the Tikka. Barrel lengths are 22 7⁄16 inches (57 cm.) in standard cartridges, 24 3⁄8 inches (62 cm.) in magnum cartridges. Depending on caliber and scopeĬhoice, weight of rifle and scope will run in the range of 6 3⁄4 to 7 1⁄4 pounds. Rifles for magnum cartridges are three ounces heavier. Weight of the T3 Lite is just six pounds, three ounces, while wood-stocked T3s weigh six pounds ten ounces, both weights for standard cartridges. I was concerned it might be brittle, so I took a non-marring nylon mallet and gave the stock a few whacks in various places, with no effect. There’s no need for pillars around the stock screws, as the hard stock material has no more give to it than steel. The stock is made of a very “hard” synthetic. With the barreled action removed, grasping the pistol grip and fore-arm and twisting hard, I could detect no movement at all in the stock. Unlike some lightweight, injection-molded stocks the T3’s stock is extremely rigid. I was pleasantly surprised by the lightweight synthetic stock. It also makes it easy to manufacture the stock to similar dimensions, enhancing stock/receiver fit. The uncluttered, simple shape of the receiver makes it easy to machine to precise dimensions. Manufacture is no doubt simpler and less costly than receivers with integral recoil lugs, or designs with the recoil lug sandwiched between barrel and receiver. When the barreled action is bolted into the stock, the recoil lug engages a slot cut in the bottom of the receiver. The recoil lug, a flat steel plate, fits snugly in a recess in the stock. T3s for short cartridges are fitted with a longer bolt stop so bolt throw is shorter.Ĭurrently the only options, other than cartridge choice, are wood with blued steel, or synthetic stock with stainless or blued steel. In addition there are Target, Varmint, and Long Range Hunter variations.Īll T3s are made on the same long action. The Whitetail Hunter is offered in both short and long actions, right or left hand versions, wood or laminated stocks. Both are fitted with hammer forged barrels, the same barrels as are used on the much more costly Sako rifles.Ĭost savings are achieved with the T3 by offering fewer options. The two-position safety locks sear and bolt handle. The T3 uses the same fine single-stage adjustable trigger as the Whitetail Hunter. Even though this is a two-lug action, bolt lift is a relatively short 70 degrees, leaving plenty of clearance between bolt handle and scope. Bolts use twin forward locking lugs, a Sako-type hook extractor, and spring-loaded plunger ejector. There’s plenty of steel in the thick, high side rails, making for a very rigid action. The T3 bolt knob is hollowed out while that on my Whitetail Hunter is solid. The magazine locking latch is on the side of the rifle in the Whitetail Hunter, and on the front of the magazine in the T3 series. The Whitetail Hunter also has a notch in the receiver ring to accept a stud in the scope ring, intended to keep theīoth use detachable, single-stack box magazines. My older Tikka has a larger, squared-off ejection port with ring grooves on the receiver bridge and front receiver ring. Scope rings to fit the integral receiver grooves are included with each T3.
WHICH TEMPLATE FITS THE SAKO FINNBEAR RIFLE IN THE LIMB SAVER PRECISION FIT RECOIL PAD FULL
The T3 has a smaller ejection port, with the integral grooves for scope rings running the full length of the receiver. I compared it to a Tikka Whitetail Hunter (Stainless Synthetic) from my gun safe.Īction differences are quite minor. The test sample on consignment was a T3 Lite Stainless in. Newest members of the Tikka line are the T3 Hunter (wood stock) and T3 Lite (synthetic stock).
Both Sako and Tikka are owned by Beretta, giving them access to Beretta’s well-established and extensive dealer and distributor network.
Tikka rifles are manufactured in Finland by Sako. Tikka rifles are rapidly earning a fine reputation for accuracy, quality and value with American hunters.